2x Bond It PU5 5 Minute Rapid Polyurethane Multi Purpose Wood Adhesive Glue - 300ml

Description:
A one part, solvent‐free, rapid setting, moisture curing polyurethane thixotropic gel specially formulated for
water‐resistant bonding and fast setting (BSEN204 D4 Classification).

Uses
Bond It PU RAPID WOOD GEL can be used in joinery and
carpentry, for bonding garden furniture, staircases, boats, wooden
constructions, sandwich panels and insulation materials. It has
excellent adhesion to wood, chipboard, laminate, metals,
polyurethane, expanded and extruded polystyrene foams, mineral
wool, concrete, stone, bricks, gypsum boards and all traditional
porous substrates. It is also an ideal adhesive for fixing carpet
grippers and stair nosings. This product is seawater proof and is
resistant to acid and chemicals.

Preparation
Ensure all surfaces are clean, dry and free from grease, oil or any
other contaminants that may hinder adhesion. The substrate must
also have a maximum humidity of 30%RH.

Application
WEAR GLOVES. Carefully cut the tip of the cartridge taking care
not to damage the threaded area. Screw on the nozzle supplied
and cut to an angle of 45°. Apply using a standard sealant gun to
one of the substrates, or to both if the materials are porous.
Assemble immediately (within 5 minutes) and clamp for at least 1
hour. Pressing the materials during curing is necessary to reach
the highest possible end strength.
The product will foam slightly on application to fill any small gaps.
Clean away any residue immediately with a dilute cleaning
solution, do not allow to set.

Setting Time
Bond It PU RAPID WOOD GEL will begin to skin after
approximately 5 minutes. Fast set will be achieved after
approximately 10 minutes with final bond strength after 12 hours.

Coverage
150-250g/m2
.
Container Size
300ml plastic cartridge.

Colour
Translucent gel.

Shelf Life
9 months from date of manufacture, when stored in original,
unopened cartridges.

Storage Conditions
Store in cool, dry and well ventilated conditions between 5-25oC.

Disposal of Containers
Do not leave empty containers where residue could be harmful to
children, animals or the environment. Remove any containers to a
central disposal point in accordance with local regulations.

Health & Safety
Please refer to separate material safety data sheet for full
handling, use and storage instructions. Keep out of reach of
children. It is the users responsibility to determine suitability for
use. If in doubt contact our Technical Department for advice.
Note: this information is for general guidance only, since site conditions
and labour are beyond our control. It is recommended that users make
their own tests to determine suitability.
HANDLING INSTRUCTIONS:
WEAR GLOVES/ SKIN COVERING AT ALL TIMES. However, if your
skin comes into contact with PU5 follow these instructions. Please
note in some cases skin turns black. If in any doubt contact a
medical professional, show the packaging and/or the MSDS
available for download from www.bonditgroup.com.
1. Wipe adhesive off with a dry cloth or paper towel. If you just
touched the glue, and it hasn’t yet begun to dry, you should be
able to remove it this way.
2. Wash your hands with soap and cold water. If the adhesive
hasn’t started hardening, you have a chance of washing it off. The
window for this is small so act quickly.
3. Exfoliate. Use a pumice stone or other gritty textured material
(eg. soap with sand in it) to rub at the glue until it comes off. Do
this slowly and patiently. Exfoliating too vigorously can damage or
burn your skin. Alternate between exfoliating and rubbing the
area with your own hand to reduce friction. The glue should begin
to ball up and come off.
4. Avoid acetone (nail varnish remover). Acetone will make the glue
stick to your skin as it removes your natural oils. Only consider
acetone if two body parts are stuck together in such a way that
exfoliating is not possible. If this is the case, soak the areas in pure
acetone until the glue dissolves enough to pull the skin apart.
Forcing this process can tear open the skin, so be patient and work
the skin apart slowly.
5. Use a cotton ball dipped in olive oil or vegetable oil to rub off the

last remaining bits. This allows you to scrub a little harder without
tearing your skin open with the exfoliate. The oil will also act as a
moisturiser to your skin.
6. Wash your hands thoroughly. Once you have removed all the
glue, it is important to wash your hands thoroughly with soap and
water to remove any remaining chemical residue.
7. Moisturise. PU5 glue will dry out your skin, coupled with
vigorous exfoliation and hand washing, the natural oils in your skin
will likely be stripped causing mild irritations. Use a good hand
lotion to soothe the area.

Specification Summary
Appearance Translucent thixotropic paste
Skinning Time 5-10 minutes @ 20o
C and 50%RH
Final Setting @ 20o
C 24 hours @ 50% RH
Press Time @ 20o
C 60 minutes @ 50% RH
Solid Content 100%
Density 1.15 ± 0.03 g/cm3
Viscosity @ 20o
C 400,000 +/- 100,000 mPas Brookfield
RVT Sp7 @ 5rpm
Application Temperature Limits +5 to 35oC
Shear Strength (beech to beech) After 15 mins >.50Kgf/cm3
After 24 hours >80Kgf/cm2
Temperature Resistance -30 to + 100oC
Tear Resistance up to 130Kg/cm2
UFI 8390-Y0UK-A00E-521T

Product Details:
Colour: Translucent
Code: BDAPU5
Size: 300ml
Barcode: 5060021363398

Package Content
2x Bond It PU5 5 Minute Rapid Set Polyurethane Multi Purpose Wood Adhesive Gel Glue